Microscraper 500 Chip Conveyor and Coolant Tank ~Metal Shaving Filtration System~
From
Turbo Systems Inc. (LNS America Inc.)
Chip and Coolant Management Experts
In very good condition. A good power washing could have it looking like new!
Some of the inexpensive scrappers need to be replaced or reinstalled.
The information we have about this unit is that which Turbo Systems Inc. (previously H & W Corp) has been able to provide us based on the unit's model and serial numbers. They are extremely helpful can be contacted directly to obtain any further information that you might need.
This chip conveyor is designed to collect metal shavings from a machining center (such as a a Takisawa or a Kitamura HX400 Machining Center) and eject them into a collection bin. Strong permanent magnets run directly beneath the conveyor belt. The magnetic effect is withdrawn at the end and the small chips drop down.
Specifications:
Model #6385-8009 Serial # 355240 Belt width: 12” length: 110.74” Pitch: 1.5” Speed: fixed at 4fpm Top mount motor 60 Hz 78.74” x 80.76” x 10.74” coolant tank 208/230/460 VAC
From the Turbo Systems / LNS Systems Website:
The MicroScraper 500 is our most economical chip conveyor incorporating coolant filtration, to 500 microns nominal. The MicroScraper 500 handles medium to light chip loads including brass, steel, cast iron and aluminum. This conveyor is ideal for chips from most casting applications and processes most materials with good chip control.
Maintenance Free Coolant Filtration
Many of today’s value priced machine tools require filtering conveyors. The MicroScraper 500 was designed as a low cost, low maintenance conveyor to solve this application need.
Coolant and chips flow from the machine into the watertight frame of the MicroScraper 500. Filter boxes, strategically located along the conveyor load section, allow the coolant to escape into the machine sump providing 500 micron filtration. Brushes attached to the conveyor’s scraper bars provide a self cleaning method to wipe contaminants from the boxes as the conveyor belt advances for maintenance free coolant filtration.
Designed For Production Efficiency
Inexpensive parts, such as aluminum investment castings, create small chips which are hard to keep out of machine sumps. Expensive filtering conveyors are hard to justify because of the low cost of these parts.
The scraper conveyor design of the MicroScraper 500 provides an excellent method of removing small broken chips in a medium to light chip load. The low conveyor investment makes this an ideal choice for small VMC and drilling and tapping machining centers. Materials like aluminum, brass and cast iron are ideal applications.
Coolant Flow and Filtration
Coolant flow ranges greatly from machine to machine and the flexibility of the MicroScraper 500 can handle most applications.
Each filter box is automatically cleaned during normal conveyors operation. Coolant flow and optimal filtration is assured. By adding or deleting filter boxes, coolant flow is adjusted to the requirements of the maximum machine flow rate.
Minimal Coolant Loss = Cost-Effective, Environmentally Friendly Operation
Coolant loss is a common problem caused by conveyor belt carry out and wet chips dropping from the conveyor. Special design considerations were taken into account on the MicroScraper 500 to eliminate wet chips.
The chip discharge area offers a special design to ensure dry chips drop into the chip hopper. An angled shelf provides time for the chips to drain until the next scraper forces more chips onto the shelf, pushing the initial load into the hopper. Less coolant loss and post processing of the chips are the obvious advantage.
Compatible For Numerous Machine Designs
Many machine designs have low discharge points for chip and coolant flow. Is the MicroScraper 500 useable for these applications?
Low profile frame designs are available for situations where the coolant and chip discharge are low to the floor increasing the number of machine designs the MicroScraper 500 is suitable for.
Compared to other types of filtering conveyors, Turbo’s MicroScraper™ offers an exceptionally economical system for providing coolant filtration in combination with chip removal.
The self-cleaning filter boxes mean no disposable filter medium is required to filter particles to 500 microns. Combined with a low maintenance scraper conveyor design, it provides a low cost, highly reliable system.
The MicroScraper handles medium to light chip loads and processes most materials with good chip control, such as brass, steel, cast iron, and aluminum. It is ideal for chips from most casting applications.
Top 3 Features and Benefits
1. Midrange Applications: Drag links scrape chips along the bottom of the conveyor body and up an incline for disposal. Ideal for a wide variety of small and medium size chips including aluminum, brass, and some steel and cast iron applications.
2. Dry Chip Disposal: Designed to minimize coolant loss from the discharge. Less coolant loss and drier chips provide a more cost-effective, environmentally friendly operation.
3. Coolant Filtration: Each filter box is automatically cleaned during normal conveyor operation. Coolant flow and optimal filtration are assured. Adding or deleting filter boxes adjusts coolant flow to the requirements of the maximum machine flow rate.
We can arrange shipping at very competitive rates.
Disclaimer: Descriptions and photos are posted by the owners of the equipment. Bid-on-equipment.com cannot guarantee their accuracy. No warranty is made regarding condition or suitability for any purpose. Contact us to arrange an inspection or a conference call with the owner. Inspection is encouraged. Items purchased cannot be returned.
1-847-683-7720
times.
Exhibit