28in AC HORN Modular Rotary Oven | Batch Ovens

    Browse our other
    Batch Ovens

    Item Details

    Item Id 393228
    Item #: 393228
    Item: 28in AC HORN Modular Rotary Oven
    Model #: MRO-28-1 28” ROTARY OVEN
    Serial #: N/A
    Year Built: 2016
    Location: Wisconsin
    Price: $120,370.00

    Description

    Like New!! AC Horn Manufacturing MODULAR ROTARY OVEN, 28” DRUM

    Item A: INFEED CONVEYOR TO SURGE FEEDER
    Conveyor built to fill feed hopper of the MRO-28” surge feeder.

    • 304 Stainless construction
    • 60° conveyor body
    • Built on portable frame with locking swivel castors
    • Intralox Series 800 belting with 3” scoop flights, 6” spacing
    • Conveyor belt is 18” wide
    • Built with 304 SS side panels
    • Infeed hopper bolted to conveyor with adjustable product feed gate
    • Includes SS discharge chute
    • 1/3 HP Drive Motor, single speed

    NOTE: Conveyor is designed for manual filling using 50 lb bags (If Super Sack is used to fill conveyor then a feeder may be required)

    Item B: SURGE HOPPER & AUGER FEEDER ASSEMBLY WITH STAND
    • Surge hopper with two level sensors to monitor product infeed rate
    • Feeder assembly with rotating auger to move product consistently

    Item C: MRO-28-1 28” ROTARY OVEN
    Single Zone, Wash-down Duty Machine designed to dry pumpkin seeds. Final capacity will depend upon factory testing results at AC Horn. Capacity will vary and is dependent upon surface area and moisture content of product at infeed and discharge.

    Includes the Following Features:

    CABINET
    • Full length, wash-down duty cabinet, with 304SS Exterior and Interior components.
    • All exterior and interior welds to be continuous
    Interior laminar baffling, with four (4) Manual Fines Traps to allow in-process cleanout
    • Two (2) Access Doors in fan plenum, and (2) full-length Access Doors in in heat transfer plenum to allow ease of insp-Temp fiberfill insulation between double wall construction
    • Circulating air distribution system stabilizes air flow along the drum within +/- 10%
    • Cabinet seals around access doors, plenum chambers, and fines traps
    • Slip joint foot pads to accommodate a ¼” per foot floor slope
    • Sloped roof wherever feasibleection, maintenance and sanitation
    • High

    DRUM ASSEMBLY
    • 304SS Rotating Drum, 28” diameter continuously welded flighting and CEMA IV finish
    • Three (3) Product Lifting Paddles (1/8” x 2” tall)
    • 1/8” x 1” Tee Ribbon, welded continuously on carrying side of auger flight
    • Turbo Inlet Cone, Roller Rings (304SS), and Connection Flange
    • Drum Screen with 3/16” diameter perforation (40% open area)
    Discharge fabricated with Distribution Vanes to even out the flow of exiting product

    DRUM DRIVE
    • Drum Drive Assembly includes 304SS Mounting Frame and Guard
    • Drum and Reducer Sprockets, Roller Chain, and Guide Assembly
    • Wash-down duty Gear Reducer selected to provide a process dwell time of 30 seconds – 6 minutes for different products
    • Paint free, wash-down duty motor (3/60/460 VAC)
    • Four (4) 304SS Drum Support Assemblies, with Remote Lube, Compression Springs

    HEAT TRANSFER SYSTEM
    • Heat Transfer System includes 1,000,000 max btu/hr Burner, complete with fractional HP Combustion Air Blower
    • Modulating Control Valve, Shut-off Valves, regulators and gauges for Natural Gas input or Liquid Propane input
    • Pilot ignition and flame rod for flame detection, using standard Eclipse Burner Controls
    • 304SS Circulating Air Plug Fan, with paint free, wash-down duty motor (3/60/460 VAC), belt drive, and guard
    • 304SS Gas Train Awning and Fire Peeper. Circulating Air Fan to range between 25% & 100% maximum speed. Process Air Temperature may be set between 250 °F & 500 °F (2) Process Air Thermocouples located in Circulating Fan Plenum
    • RH / Temperature sensor located in Exhaust Duct

    CONTROLS
    • Nema 4x Electrical Control Center includes fused panel disconnect, with circuit breaker protection for each drive or motor
    • Feeder Speed is set using 4 – 20 mA control. Variable Speed Drives for Rotating Drum, Circulating Fan, and Exhaust Fan
    • Control Transformer, Panel AC Unit, and Arc Flash Box. Ignition and Flame Safety control with gas and air flow interlocks
    • 8” Touch Screen Display and PLC integrate all Rotary Oven functions
    • Spanish-language option available

    Key Words: Snacks, nuts, seeds roaster, almonds, pumpkin

    Additional Prep Fees May Apply

    Shipping

    Height: N/A
    Width: N/A
    Length: N/A
    Weight: N/A
    Prep Fee: $0.00
    Registered Customers can request shipping quotes free of charge. Shipping Quotes take 1-3 Business Days to Process

    charticon This item has  today
    moneyicon Have one to sell?
    Sell
    Need Financing? FinanceLink

    Testimonials

    • "The biggest demand for manufacturers today is to become operational as quickly as possible and Bid on Equipment provides this solution." - Dave M.
    • "The strength of their site is how often our machinery comes up on web searches." - John G.
    • "We appreciate BoE... Always helpful, friendly and very professional." - Ali L.
    • "If you have questions about machinery you're buying they will find someone who can help. Everyone I talk to here is very friendly." - Tim Y.
    • "BoE is a powerful site that has yielded great results for our company. If you need to buy or sell equipment, I recommend this site." - Michael M.
    • "BoE keeps the engine turning and its potential is limitless. They take out the nonsense that you find on auction sites." - George P.
    • "I have sold 2 large Electric Motors through Bid On Equipment. They got them sold within a month!" - Richard B.
    • "The best thing to happen to our company, the personnel are fantastic..." - Ron W.